What does AF mean on my Maytag dryer?

AF. An “AF” error code in your Maytag dryer’s display indicates that the appliance is suffering from low airflow. In most cases, the airflow is reduced due to a clogged vent or lint screen. In addition, the vent may be kinked or bent so air has difficulty reaching the dryer.

An AF (Restricted Air Flow) error code indicates that the lint screen or house vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

One may also ask, how do I fix my Maytag dryer? AF” flashes if a restricted airflow condition exists. Check to make sure the lint screen is clean, the door seal is in place and the vent is not obstructed. Since you are certain that in your case this is not an issue then you may have a faulty sensor. You will need to replace the faulty sensor to fix this problem.

In respect to this, what does AF mean on the dryer?

Restricted air flow

What does PF mean on a Maytag dryer?

Power failure

Can you reset a Maytag dryer?

Full Reset It is not uncommon to need to reset a dryer after an error code has been resolved or if the dryer shut down to prevent a thermal overload. Disconnect the power to the Maytag dryer and wait 30 minutes. After 30 minutes, restore power and make a new selection.

What does f01 mean on a Maytag dryer?

Maytag Bravos Dryer Error Code = F01 Error Condition = Main Electronic Control Board Fail. Check or Repair Needed = Remove the dryer from power for 10 minutes. Apply power back to the dryer and if the code returns you need to replace the main electronic control board.

What is e1 on Whirlpool Duet dryer?

The Whirlpool Duet Dryer Error E1 means the control has detected that the thermistor is open. This error can be a wiring issue from the control to the thermistor or a bad thermistor.

What does the code AF mean on a Whirlpool Cabrio dryer?

An AF (Restricted Air Flow) error code indicates that the lint screen or vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

How do I fix the l2 code on my Maytag dryer?

Replace the dryer fuse(s) or turn off the household circuit breaker for the dryer for one (1) minute, to reset the circuit breaker, then turn on the circuit breaker. Confirm that the power cord is properly installed. Refer the Installation Instructions for details. Select a Timed Dry heated cycle and restart the dryer.

Why does my dryer keep saying Check vent?

The Check Vent Light is located on the console of some dryers (see diagrams below) and indicates that dryer airflow is restricted. Your dryer requires adequate air flow to ensure proper performance and dry times.

What does it mean when your dryer says f01?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. Be sure to unplug the washer before accessing internal components.

What does PF mean on Whirlpool Cabrio dryer?

power failure

What does F mean on Kenmore Elite dryer?

F-40. Communication error between the main electronic control board and the blower motor control board. Check/ Repair. Unplug the dryer and check the wire harness connections between the blower motor control board and the main electronic control board.

How do you clean the lint out of a Whirlpool Cabrio dryer?

To clean inside the dryer, unplug it and turn off the gas, then open either the top or the front. The procedure is the same for gas and electric dryers. For dryers with a top lint filter and a solid front panel, remove the lint filter and take out the two screws on the side of the lint filter opening.

How do I reset my Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.” Choose a new cycle and press “Start” to begin. Turn off and disconnect the Cabrio if the error or problem persists. Wait several minutes before restoring power. Contact Whirlpool for assistance if the unit will not reset.