How do you reset a GE Z Wave dimmer?

Press to reboot the Smart Switch. Press and hold (about 5 seconds) until the Wi-Fi status LED blinks amber and green alternately to initiate App-Config mode. Press and hold (about 10 seconds) until the Wi-Fi status LED blinks green rapidly to factory reset the Smart Switch.

To reset the GE In-Wall Zigbee device

  1. For switches and dimmers: Press up on the switch ten (10) times.
  2. For outlets: Unplug the outlet from the wall socket. Hold the connect button. Plug in the outlet while holding the connect button. Release the button when the LED turns on.

Furthermore, how do you reset a smart light switch? Press to reboot the Smart Switch. Press and hold (about 5 seconds) until the Wi-Fi status LED blinks amber and green alternately to initiate App-Config mode. Press and hold (about 10 seconds) until the Wi-Fi status LED blinks green rapidly to factory reset the Smart Switch.

Subsequently, one may also ask, how do I reset my GE zw4101?

The Lamp Module can be reset, but will need to be re-paired with your system.

  1. Unplug the Lamp Module from the outlet.
  2. Press and hold the button in the center of Lamp Module’s front.
  3. Plug the Lamp Module back into the outlet while holding down the button.
  4. Release the button after the Lamp Module is plugged in.

How do I reset my Smart Switch?

To reset a smart switch using the Factory Default button:

  1. Locate the recessed button that is marked Factory Default or Factory Defaults on the back or bottom panel of your device.
  2. Insert a straightened paper clip or a similar device into the hole of the Factory Default button and hold for two to three seconds.

How does Z wave light switch work?

Z-wave technology creates a wireless mesh network, which is a collection of devices that link up and communicate with each other without wires. With Z-wave technology, devices “mesh” together by sending signals over low-energy radio waves on a dedicated frequency.

How do you set up a smart switch?

How to install a smart light switch Step 1: Learn your existing wall switch and wiring setup. Step 2: Choose a smart light switch. Step 3: Remove your old light switch. Step 4: Connect your smart light switch. Step 5: Secure the smart light switch in place. Step 6: Connect your smart light switch to Wi-Fi.

What is the best Z Wave controller?

Best Z-Wave Controllers Reviewed Mi Casa Verde VeraLite. Check Price & More Details. Samsung SmartThings Hub. Check Price & More Details. HomeSeer HomeTroller-SEL Home Controller. Check Price & More Details. Vera Control VeraEdge Home Controller. Nexia Home Intelligence Z-Wave Bridge. Wink Hub 2 Z-Wave Controller. Aeon Labs Aeotec Z-Wave Z-Stick.

How do you reset an AVI light switch?

To perform a device reset. Plug-in or power the device. Hold the button down on the device for 30 seconds. The device’s LED will blink in sets of two to acknowledge the reset (note that the Outdoor Switch does NOT have a status LED) If the light does not blink–repeat this process–hold the button longer.

How do you program SmartThings?

Set up a SmartThings Hub From the Home screen, touch the Plus (+) icon and select Add device. Touch SmartThings, touch Wi-Fi/Hub, and then SmartThings Hub IM6001-V3. Select how you’d like to connect your Hub by touching Wi-Fi or Ethernet. Follow the in-app instructions to connect your Hub, which are reproduced here:

What is Z Wave technology?

Z-Wave is a wireless protocol harnessing low-energy radio waves to help smart devices or appliances communicate successfully with one another. Zensys from Denmark developed Z-Wave in 2001. A wireless mesh network, Z-Wave can support up to 232 devices.

What is a Zwave switch?

On/off Smart Switches are basic on/off light switches that can be turned on/off at the switch, remotely, or via scene control.

How do I make my GE Smart Switch ring?

Connecting a Z-Wave sensor to your Ring Alarm is much like adding any of Ring’s own sensors. Click the large “+” symbol to “Set up a device” on the Ring app home screen and choose “Security Devices.” From there, choose the type of device. In this example, I’m adding a GE Door Hinge sensor, so I’ll click “Sensors.”