Car stereos run on 12 volts DC electric current, but you can connect a car stereo to 110 volts AC and make it work inside your home.
Usually, you’ll be installing a 4-channel amplifier with speaker-level inputs. The best way to connect it to a factory system is to tap into the stereo’s speaker outputs for the amp’s input signal. Then send the amp’s outputs back to the stereo’s harness, and on to the speakers through the factory wiring.
Subsequently, question is, can you hook a car amp up in your house? If you‘ve got a car amplifier you‘d like to use in your home, there’s one major obstacle to overcome: how to power the amplifier. Wall outlets provide 110-volt AC power, but amplifiers require 12-volt DC power. You‘ll have to do a little extra wiring, but the problem is not insurmountable.
Subsequently, one may also ask, can you hook up a car subwoofer and amp to a home stereo?
A subwoofer meant for a car stereo can often give you better sound quality on your home theater system. The problem is that this subwoofer requires an amplifier that runs on 12-volt power, like from a car battery. The subwoofer and amplifier would fry if either was plugged into a home power socket.
How do you wire a car stereo to an outlet?
You need a 12V power cord to use your car stereo power supply for home use, but you can easily get that from a hardware store. Cut the end of the power cord and connect the black wire with the line of white around the stereo’s red and yellow wires. Make sure every wire is completely covered before you plug it in.
Can I use a car subwoofer for home audio?
Never fear, for the intrepid do-it-yourselfer, it is totally possible to use your car audio subwoofer in a home theater setup. The most important thing to be wary of is electricity requirements, because the car subwoofer is designed to run on considerably lower voltage than you have running through the wires at home.
How do I connect my speakers to my amp?
On the back of your amplifier, you should find the speaker outputs. Connect your speaker wires to these outputs — one into each output. The speaker wires are usually just bare wire ends. Make sure you’re connecting the left and right output speaker wires into their corresponding left and right speakers.
Can you plug a car amp into wall socket?
If you’re in that position, you might occasionally want to use your car amp in the house to drive a set of speakers. Car amplifiers run on 12V DC power and your wall outlet puts out 110V AC, so making them play together nicely takes a bit of persuasion.
How do you hook up car speakers to a house?
How to Connect Home Speakers to a Car Stereo Open the trunk and disconnect one pair of speaker wires from the existing automotive speakers. Note which wire is positive and negative when removing these wires. Look at the home speaker. Notice the type of connection that it has. Plug an RCA plug into the home speaker. Cut the other RCA plug from the RCA cable.
What is the difference between a car subwoofer and a home subwoofer?
Another primary difference between a car and home subwoofer is the efficiency of the speaker. In general, home subwoofers are usually much more efficient than their car counterparts. For instance, it is not uncommon for a home-use subwoofer to create around 90 to 95 dB of sound when driven by 1 watt of power.
What cable do I need to connect subwoofer to receiver?
The preferred method of connecting a subwoofer is through the Subwoofer Output (labeled as ‘SUB OUT’ or ‘SUBWOOFER’) of a receiver using an LFE ( an acronym for Low-Frequency Effects) cable. Almost all home theater receivers (or processors) and some stereo receivers have this type of subwoofer output.
Can you use car speakers with a home stereo?
But you do need to make sure your home stereo unit can handle the lower impedance of most car speakers. The typical car speaker is four ohms and most home receivers are designed for eight ohms. In fact different speakers that have passive crossover components wired inline should be connected in parallel.
How do you hook up a subwoofer without an amp?
You can use the following: Connecting Using The LFE Subwoofer Output. On the box of the subwoofer, there is a place labeled “SUBWOOFER” or “SUB OUT” which you can connect to the car stereo using an LFE (low-frequency effects), which is found on most of them. Connect Using Speaker Level Or Stereo RCA Output.
What is the difference between car speakers and home speakers?
The difference between car speakers and home speakers is that car speakers are designed to be used in cars. Car = small space. Even computer speakers don’t sound half bad if you’re right next to them in your little bedroom.